Methylcyclohexane production under fluctuating hydrogen flow rate conditions

Energy storage using liquid organic hydrogen carrier (LOHC) is a long-term method to store renewable energy with high hydrogen energy density. This study investigated a simple and low-cost system to produce methylcyclohexane (MCH) from toluene and hydrogen using fluctuating electric power, and developed its control method. In the current system, hydrogen generated by an alkaline water electrolyzer was directly supplied to hydrogenation reactors, where hydrogen purification equipment such as PSA and TSA is not installed to decrease costs. Hydrogen buffer tanks and compressors are not equipped. In order to enable MCH production using fluctuating electricity, a feed-forward toluene supply control method was developed and introduced to the system. The electrolyzer was operated under triangular waves and power generation patterns of photovoltaic cells and produced hydrogen with fluctuating flow rates up to 7.5 Nm³/h. Consequently, relatively high purity of MCH (more than 90% of MCH mole fraction) was successfully produced. Therefore, the simplified system has enough potential to produce MCH using fluctuating renewable electricity.     

Malaysia’s electricity market structure in transition

The Malaysian electricity industry evolved from a vertically integrated utility into a single-buyer model, which considered a precursor to deregulation and a competitive market. This study considers electricity sector reform in Malaysia and proposes a market structure for the industry. We focus on the single-buyer model and the pool model for the analysis with the recommendation on reform stages required to ensure a smooth and successful market transition. A smooth transition from regulated market into deregulated market will ensure market stability and sustainability of the energy market. It will also provide enough time for the market participants to adapt and transit from regulated to deregulated energy market.     

Gas‐phase removal of indoor volatile organic compounds and airborne microorganisms over mono‐ and bimetal‐modified (Pt,Cu, Ag) titanium(IV) oxide nanocomposites

The photocatalytic deactivation of volatile organic compounds and mold fungi using TiO₂ modified with mono‐ and bimetallic (Pt, Cu, Ag) particles is reported in this study. The mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide photocatalysts were prepared by chemical reduction method and characterized using XRD, XPS, DR/UV‐Vis, BET, and TEM analysis. The effect of incident light, type and content of mono‐ and bimetallic nanoparticles deposited on titanium(IV) oxide was studied. Photocatalytic activity of as‐prepared nanocomposites was examined in the gas phase using LEDs array. High photocatalytic activity of Ag/Pt‐TiO₂ and Cu/Pt‐TiO₂ in the reaction of toluene degradation resulted from improved efficiency of interfacial charge transfer process, which was consistent with the fluorescence quenching effect revealed by photoluminescence (PL) emission spectra. The photocatalytic deactivation of Penicillium chrysogenum, a pathogenic fungi present in the indoor environment, especially in a damp or water‐damaged building using mono‐ and bimetal‐modified (Pt, Cu, Ag) titanium(IV) oxide was evaluated for the first time. TiO₂ modified with mono‐ and bimetallic NPs of Ag/Pt, Cu, and Ag deposited on TiO₂ exhibited improved fungicidal activity under LEDs illumination than pure TiO₂.     

Visualization of temporal differences between dominant perceptions in temporal dominance of sensations (TDS) and temporal check-all-that-apply (TCATA) perceptions using dominance-highlighted TCATA (dTCATA) curves

The temporal dominance of sensations (TDS) method measures dynamic changes of panelists’ attention to the sensory attributes of products. The temporal check-all-that-apply (TCATA) method measures all sensory attributes perceived at each moment of an evaluation. However, unlike in TDS, significant levels cannot be calculated in TCATA. This study proposes the use of dominance-highlighted TCATA (dTCATA) curves, which are highlighted TCATA curves that show significant time periods for the TDS data of different panels. Twelve R&D panelists evaluated five commercial corn soups using the TCATA method. Then, 125 consumer panelists evaluated the same products using the TDS method. The dTCATA curves showed TCATA curves for all attributes for each product evaluated by the R&D panel highlighted with the dominance rates identified by the consumer panel in the TDS evaluation. For example, for product 1, some attributes (sweet, viscosity) showed relatively high citation proportions in the TCATA evaluations of the R&D panel and significant dominance rates in the TDS evaluations of the consumer panel. In contrast, consommé flavor showed relatively low citation proportions in TCATA but significant dominance rates in TDS. By merging TDS and TCATA data, we could compare consumers’ dominant sensations with the evaluations of R&D panelists. This comparison could provide useful insights to product developers. In some cases, we observed attributes with significant dominance rates that were under-identified by the R&D panel in TCATA. This could suggest that most of the R&D panel may not have perceived these attributes; therefore, during product development, these attributes should be carefully considered.     

Investigating the effect of SPS‎ parameters on densification ‎and fracture toughness of ZrB2-SiC nanocomposite‎

In this study, the effect of sintering parameters on densification and fracture toughness of spark plasma sintering ZrB₂-SiC nanocomposites was evaluated. For this purpose, ZrB₂-??30?vol% SiC nanocomposites in the conditions of ?1600?°C-4?min, 1700?°C-4?min, 1800?°C-4?min, 1800?°C-8?min, 1800?°C-12?min? were sintered.? Scanning Electron Microscopy (SEM) was used in order to investigate the ?microstructural variations. The bulk density was measured accoring to ASTM C 373–88. Single edge notch beam (SENB) method was used to ?determine the fracture toughness of samples. Microstructural observations showed that ?an increase in sintering temperature led to slight ?increase in SiC grains size but no sensitive variation in ZrB₂. However, increasing the sintering time resulted to increase both ZrB₂ and SiC grain size. Also, it was found, temperature and time ascent always increases the relative density. In addition, it was concluded that optimal temperature and time to reach the highest fracture toughness are 1800?°C and 8?min, respectively. Investigation of SEM images of the Vickers indent and their path propagation showed that the deviation and branching of crack are the most important toughening ?mechanisms in ZrB₂-SiC nanocomposites.?     

Integrating TTF and UTAUT2 theories to investigate the adoption of augmented reality technology in education: Perspective from a developing country

Augmented reality (AR) has gained increased recognition in varying fields, in particular educational contexts. In the wake of the Covid-19 pandemic, home-based learning becomes a reality and is already in place across the globe, and learning via augmented reality technology will help learners comprehend learning content in a more creative frame of mind than ever before. Very little research has examined the adoption behavior of augmented reality in developing country perspectives. Therefore, there is a pressing necessity to understand the dynamics of augmented reality adoption for the benefit of motivating and inspiring students to adopt this highly innovative and impactful type of technology in the learning process. Against this background, the authors proposed and tested a model based on integrating Task-Technology Fit (TTF) and UTUAT2 theories. The results reveal the positive effect of task technology fit, performance expectancy, effort expectancy, social influence, facilitating condition, and hedonic motivation on behavioral intention (BI) in the adoption process of augmented reality in educational settings, where price value is found to exert little influence on behavioral intention. This model explains 49% of the variance in intentional behavior to adopt AR technology in the educational context. The conclusions of this study will add to the literature more informative knowledge leading to increased awareness of the dynamics and behaviors of AR adoption in a developing country perspective. We present and discuss the theoretical contributions and practical implications of our findings.     

A dinuclear iron complex as a precatalyst for water oxidation under alkaline conditions

Water oxidation is a key reaction for water splitting. The decomposition of Fe-based-molecular structures toward Fe-based oxides is a promising method for oxygen-evolution reaction (OER) through water oxidation. The decomposition of Fe-based-molecular structures method results in a slow decomposition of precatalysts and forms Fe oxide-based catalysts. In this study, the Fe species formed through the decomposition of a dinuclear Fe(III) complex under OER is investigated by X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersive spectrometry, X-ray diffraction, and the electrochemical method. In addition, using Ni(OH)₂, a new approach is reported for detecting trace Fe species on the electrode surface. The resulting Fe oxide-based catalyst shows a catalytic current with an onset of 621 mV overpotential and the Tafel slope of 113.7 mV/decade at pH 11 in a buffer phosphate.     

Ambient electrosynthesis of NH3 from N2 using Bi-doped CeO2 cube as electrocatalyst

The synthesis of ammonia (NH₃) from electrochemical nitrogen reduction reaction (NRR) under environmental conditions is a promising technology. Compared with the traditional artificial nitrogen fixation process by the Haber-Bosch process, electrochemical nitrogen reduction reaction (NRR) requires no harsh reaction conditions. In this work, we report that Bi-doped CeO₂ nanocubes show high NRR activity as electrocatalysts. The NH₃ yield of 17.83 μgh⁻¹ mg⁻¹_cat. and the Faradaic Efficiency (FE) of 1.61% at −0.9 V are achieved in 0.1 M Na₂SO₄. The performance is much higher than that for the traditional CeO₂ nanoparticles. The detailed analysis indicates that both the Bi doping and the cube morphology are critical for this encouraging NRR performance. The mechanism for improving NRR is further explored with first-principle calculations, demonstrating the importance of Bi-doping for performance enhancement.